Find the first sticking point.![How to crack a combination lock in seconds How to crack a combination lock in seconds](/uploads/1/2/6/0/126083661/839467204.jpg)
A different method for finding the third number is to test the catch. Spin the dial clockwise a few times to reset the lock and set it at 0. Apply upwards pressure on the shackle and turn the dial clockwise.
- As you turn the dial CW with tension on the shackle, you will come to the first clockwise stopping point where you can't turn the dial anymore. Make note of where it stops. Sometimes, the dial will stick right on the numbers, but sometimes the sticking point will be between the numbers. If so, record the number to the half (example: 22.5).[3]
- While continuing to apply tension to the shackle, turn the dial as far left (counter-clockwise) as you can. Make note of the first counter-clockwise (CCW) stopping point. The CCW stopping point and CW stopping point form your sticking 'range', for example, 22.5 to 10. (Note: Some 800XXX and 908xxx locks have a two number sticking range [for example, 28 to 30 and 10 to 12].)[4]
- Determine the first sticking point by finding the number that's in the midpoint of the sticking range. A range of 4 and 5 would have a first sticking point of 4.5. A range of 22.5 and 23.5 would have a first sticking point of 23.
- Each set of numbers that you find will have the same range. For example, one group may be 0.25 to 0.75 and another may be 0.5 to 0.25 on either side of the sticking points.
Download solidworks parts free. HOW TO CRACK ANY COMBINATION LOCK IN SECONDS Step 1: EXPLAINING HOW IT ALL WORKS. A combination lock. Step 2: GATHER YOUR EQUIPMENT. To be able to crack your combination lock all you will need is. Step 3: FINDING THE RIGHT DIAL. First of all you will have to thread your length. Upon reaching the second number, turn the dial to the right until the arrow is pointing to the third number of the combination. Hold the body of the lock in one hand and the curved metal bar or shackle in the other and pull the two apart to open the lock. C serialize data. Push the shackle down into the hole on the body of the lock to close the lock. Without any further introduction, let’s learn how to crack a combination safe with four easy steps. Step 1: Find The Torque Screws. There is often a “registry” plate that will accompany these safes on the front. There will be two to four hex screws here. The first thing we will need to do is remove one side of them with a basic torx screw driver. Standard Instructions for Opening a Combination Lock. Turn right three times. Stop at First Digit. Turn left one full turn passing 1st number and stop at Second Digit. Turn right and stop at Third Digit.
![How to crack a combination lock in seconds How to crack a combination lock in seconds](/uploads/1/2/6/0/126083661/839467204.jpg)
How To Crack A Combination Lock With 3 Numbers
Test for the third number.How To Crack A Combination Lock 3 Digit
![Crack Crack](/uploads/1/2/6/0/126083661/681797510.jpg)
- The lock will catch several times, allowing for slight movement back and forth between two numbers.
- Write down the number in the middle. For instance, if the lock catches between 33 and 35, write down 34 on a separate piece of paper. This is not necessarily the final number.
- The lock will also catch partway between numbers. For example, the range might be between 27.5 and 29.5. If the middle number is not a whole number, such as 28.5, do not write it down. Lock combinations are always whole numbers.
- Proceed all the way around the dial, writing down all the whole numbers where it catches. You should have four or five numbers written down.
- Most of the numbers will fit a pattern, for instance all ending in 5. The one number that does not fit the pattern is the final number in your combination.[3][4]